Vintage 551170 Dokumentacja

18865 GOLL ST. - SAN ANTONIO, TX. - 78266 ph.210-654-7171 - fax 210-654-31131969-70 MUSTANGw/o FACTORY AIR GEN IV 551170 901271 REV A 2/11/08, 69

CENTER LOUVER INSTALLATION (OPTION 1)UNDER DASH CENTER LOUVER INSTALLATION (OPTION 2) 101969-70 MUSTANG w/o AC GEN IV ASSEMBLED VIEWTEMPLATECUT OUTCEN

111969-70 MUSTANG w/o AC GEN IV LOCATE EVAPORATOR DRAIN ON BOTTOM OF EVAPORATOR CASE.IN-LINE WITH THE DRAIN, LIGHTLY MAKE A MARK ON THE FIREWALL. MEAS

HEATER HOSE & HEATER CONTROL VALVE INSTALLATIONROUTE A PIECE OF HEATER HOSE FROM THE WATER PUMP TO THE HEATER LINE COMING THROUGH THE FIREWALLAS S

(6)TIE WRAP#8 CONDENSER TOCORE SUPPORTHARDLINE081096#6 DRIER TO CORE SUPPORTHARDLINE081095CORE SUPPORTINNER FENDERWELLNOTE: VINTAGE AIR SYSTEMS REQUIR

GLOVE BOX INSTALLATIONINSTALL GLOVE BOX WITH OEM SCREWS. SEE FIGURE 13.INSTALL DUCT HOSES AS SHOWN IN FIGURE 14, PAGE 15.ROUTE A/C WIRES THROUGH 3/8 G

151969-70 MUSTANG w/o AC GEN IV S B YDRIVER SIDE DEF. DUCT 2” x 14”DRIVER SIDE LOUVER2 1/2” x 30”CENTER LOUVERDRIVER SIDE2 1/2” x 32”CENTER LOUVERPASS

189125-MUR1/4 PUSH NUTBOLT RETAINER 18289-VUB1/4-20 X 1COARSE BOLTBRACKET #6 LIQUID LINE081091 EVAPORATOR HARD LINE INSTALLATION HEATER LINE(EVAP TO W

171969-70 MUSTANG w/o AC GEN IV WIRING DIAGRAM85 8586 86 GROUNDDASH/FLOORDEFROST/PLENUMTEMPERTURE BLENDCOMPRESSOR30 AMPBLKBLKDK BLUDK BLUREDREDRED RED

HEATERCONTROLVALVE RELAYHEATERCONTROLVALVEREFER TO CONTROLPANEL INSTRUCTIONSAND PLUG IN ACCORDINGLYBINARYSAFETYSWITCHNOTE: IF USING TRINARYSAFETY SWIT

OPERATION OF CONTROLSNOTE: WHEN BATTERY POWER IS FIRST CONNECTED TO THE ECU, THE COMPUTER GOES THROUGH AN INITIALIZATIONSEQUENCE. THIS INITIALIZATION

PAGES 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13.14. 15. 16.17. 18.19. 20. 21.22.23.24.25.26. COVERTABLE OF CO

TROUBLE SHOOTING INFORMATIONSYMPTOM CONDITION CHECKS ACTIONS NOTES1.BLOWER STAYS ON HIGH SPEED WHEN IGNITION IS ONNO OTHER FUNCTIONS WORKCHECK FOR DAM

SYSTEM WILL NOT TURN ON OR RUNS INTERMITTENTLYWORKS WHEN ENGINE IS NOT RUNNING, SHUTS OFF WHEN ENGINE IS STARTED. (TYPICALLY EARLY GEN 4, BUT POSSIBLE

221969-70 MUSTANG w/o AC GEN IV DRIVER SIDE LOUVER TEMPLATECUT ALONGDOTTED LINE CENTER PUNCH&DRILL2 3/4 HOLE1969-70 MUSTANG w/o ACDRIVER SIDE LOUV

23PASSENGER SIDE LOUVER TEMPLATECUT ALONGDOTTED LINE 1969-70 MUSTANG w/o ACPASSENGER SIDE LOUVER TEMPLATECENTER PUNCH&DRILL2 3/4 HOLE 901271 R

241969-70 MUSTANG w/o AC GEN IV CENTER LOUVER TEMPLATE1969-70 MUSTANG w/o ACCENTER LOUVERTEMPLATECUT ALONGDOTTED LINE CUT ALONGDOTTED LINE 901271

251969-70 MUSTANG w/o ACFIREWALL COVER HOLE TEMPLATETHIS SIDE INSIDE OF CAR(6) 3/16HOLESOEM HEATERHOLEBLOWER MOTORMOUNTING HOLEBLOWER MOTORMOUNTING HO

EVAPORATOR KIT PACKING LISTEVAPORATOR KIT551170No. QTY. PART No. DESCRIPTION1.2.11169-70 MUSTANGEVAP. SUB CASE 76306976

** BEFORE BEGINNING INSTALLATION OPEN ALL PACKAGES AND CHECK CONTENTS OF SHIPMENT. PLEASE REPORT ANY SHORTAGES DIRECTLY TO VINTAGE AIR WITHIN 15 DA

IMPORTANT NOTICE-PLEASE READFOR MAXIMUM SYSTEM PERFORMANCE VINTAGE AIR RECOMMENDS THE FOLLOWING:LUBRICANT CAPACITIES:134a SYSTEMR-12 SYSTEMCHARGE WITH

THE HEATER CONTROL VALVE IS A NORMALLY OPEN VALVE. IT MUST BE CONNECTED TO THE ECU TO BLOCK WATER FLOW IN AC MODE. CARE MUST BE TAKEN WHEN INSTALLIN

REMOVE THE FOLLOWING:REMOVE DASH PAD, INSTRUMENT PANEL, PASSENGER SIDE PANEL AND LOWER PASSENGER SIDEDASHBOARD (RETAIN SCREWS) SEE FIGURE 1.GLOVE BOX

TEMPLATEDEFROST DUCT/ FRESH AIR CAP INSTALLATIONINSTALL DEFROST DUCT UNDER DASH AS SHOWN IN FIGURE 3 BELOW. SECURE USING OEM NUTSw/ (3) 3/16 SAE FLAT

EVAPORATOR INSTALLATIONON A WORK BENCH, INSTALL EVAPORATOR REAR BRACKET AND HARDLINES WITH PROPERLY LUBRICATED O-RINGS. (SEE FIGURE 10, PAGE 11, AND

FIREWALL COVER INSTALLATIONINSTALL (3) GROMMETS ON FIREWALL COVER AS SHOWN IN FIGURE 7, BELOW.APPLY A 1/4 BEAD OF SILICONE AROUND THE BACK SIDE OF THE